Citroen-2CV / Dyane / steering gear

Spring for gear racks thrust piece (in the steering gear). Suitable for Citroen 2CV. Or.Nr.A4422

Quality: 4

Steering gear repair set for the tie rod guide. Suitable for Citroen 2CV. Consisting of: Pin + seat bowls + guides, ball pin, rubber,

Quality: 3

• Suitable for this article
• Front axle cover sheet. (Cover at the steering gear, below the tie rod securement). Suitable fo
  8,83 €
• Front axle sliding sheet metal at the steering unit. Suitable for Citroen 2CV. Or. No.: AM44279
  7,83 €
• Front axle sliding sheet metal, safety sheet. (Sliding sheet metal on the steering unit). Suita
  1,55 €

Steering worm of 7 teeth, inclusive bearing, for Citroen 2CV. Splines (worm gears) are continuous up to the bearing. Suitable bush = 12233.

Quality: 3

Steering worm of 8 teeth, inclusive bearing, for Citroen 2CV. Good reproduction! The suitable guide bush down (10mm inside diameter) has our No. 12232. Overall length: 112,8mm.

Quality: 3

• Suitable for this article
• Steering worm bearing bush 2CV, down at the steering worm. (Needle bearings), manufacturer SKF!
  20,73 €

Steering worm of 8 teeth, inclusive bearing, for Citroen 2CV. Inside diameter: 10mm. Suitable lower bush = 12232. Overall length: 112,8mm.

Quality: 4

• Suitable for this article
• Steering worm bearing bush 2CV, down at the steering worm. (Needle bearings), manufacturer SKF!
  20,73 €

Steering worm distance disk. Suitable for Citroen 2CV. Measurement: 23.5 x 34 x 0,95mm. Or.Nr.: A442-72

Quality: 4

Steering worm bearing bush (down at the needle bearing). Suitable for Citroen 2CV. The bearing is a needle bearing! Only for steering worms with 8 teeth. Inside diameter: 12mm. Outside diameter: 18mm. Overall height: 12mm. Manufacturer SKF.

Quality: 2

Steering worm bearing bush 2CV, down at the steering worm. (Needle bearings), manufacturer SKF! Inside diameter 10mm, outside diameter 17mm, height of 12mm

Quality: 3

Steering worm bearing bush 2CV, down at the steering worm. (no needle bearing). Inside diameter 10mm, outside diameter 16mm, height of 10mm

Quality: 3

Steering worm locking cap down (the cap is hit from downside into the steering gear). 20mm. Suitable for Citroen 2CV.

Quality: 4

Steering worm nut with sealing ring. Suitable for Citroen 2CV starting from year of construction 03/1971.

Quality: 4

Steering worm nut with sealing ring. Suitable for Citroen 2CV, starting from year of construction 03/1971. From own production, with interchangeable shaft seal. Very significant.

Quality: 3

Steering worm nut shaft seal (as substitute for 12140). Suitable for Citroen 2CV, starting from year of construction 03/1971. Dimension: 19 x 27 x 5mm.

Quality: 3

Steering, repair kit (assembled). Suitable for Citroen 2CV up to Orga No. 2275, Dyane, Mehari. Consisting of the complete guide in the front axle tube, incl. new rack, 24 teeth. Good quality. This is the old version of the steering rack for a steering pinion with 7 teeth!!! Made in Europe

Quality: 3

• Suitable for this article
• Tie rods rubber, at the front axle. Suitable for Citroen 2CV4 + 2CV6.
  2,77 €
• Steering worm of 7 teeth, inclusive bearing, for Citroen 2CV. Splines (worm gears) are continuo
  39,57 €
• Front axle sliding sheet metal, safety sheet. (Sliding sheet metal on the steering unit). Suita
  1,55 €
• Screw M7x12, e.g. to fix the steeringwheel 2cv, screw is galvanized
  0,51 €

Steering unit, repair set. Suitable for Citroen 2CV. Consisting of: Guide steering unit pin, 2x slide ring, ring for the gear rack ((27,75mm + - 1/10mm), rubber under the tie rods. Reproduction. Only for LHD, cannot use for RHD.

Quality: 4 360°

• Suitable for this article
• Front axle sliding sheet metal, safety sheet. (Sliding sheet metal on the steering unit). Suita
  1,55 €
• Screw M7x12, e.g. to fix the steeringwheel 2cv, screw is galvanized
  0,51 €

Tie rods slide ring squarely (1 oversize), mounts in the steering gear. Suitable for Citroen 2CV. Reproduction from a brass alloy. Oversize: about 8 x 13 x 21mm.

Quality: 5

• Suitable for this article
• Tie rods rubber, at the front axle. Suitable for Citroen 2CV4 + 2CV6.
  2,77 €
• Tie rods ball pin, in the steering gear. Suitable for Citroen 2CV. Or.Nr.: AM4428. The surface
  8,83 €

Tie rods slide ring squarely, mounts in the steering gear. Suitable for Citroen 2CV. Reproduction from a brass alloy. Standard measurement about 8x13x20.

Quality: 3

• Suitable for this article
• Tie rods rubber, at the front axle. Suitable for Citroen 2CV4 + 2CV6.
  2,77 €
• Tie rods ball pin, in the steering gear. Suitable for Citroen 2CV. Or.Nr.: AM4428. The surface
  8,83 €

Tie rods rubber, at the front axle. Suitable for Citroen 2CV4 + 2CV6.

Quality: 3

Tie rods ball pin, in the steering gear. Suitable for Citroen 2CV. Or.Nr.: AM4428. The surface is hardened!

Quality: 4

• Suitable for this article
• Tie rods rubber, at the front axle. Suitable for Citroen 2CV4 + 2CV6.
  2,77 €
• Tie rod nut, self locking. For the securement at the steering gear. Suitable for all Citroen 2C
  0,58 €
• Tie rods slide ring squarely, mounts in the steering gear. Suitable for Citroen 2CV. Reproducti
  4,07 €
• Tie rods slide ring squarely (1 oversize), mounts in the steering gear. Suitable for Citroen 2C
  6,60 €

Tie rod nut, self locking. For the securement at the steering gear. Suitable for all Citroen 2CV, Dyane, Ami.

Quality: 3

Tie rod end cup. Improved version, made of sintered metal. Per piece (per side 2 pieces required). Suitable for Citroen 2CV., AK, Dyane, AMI, Mehari

Quality: 1

• Suitable for this article
• Spring in the tie rod end. Suitable for Citroen 2CV. Per side 1x spring is required.
  3,87 €

Front axle cover sheet. (Cover at the steering gear, below the tie rod securement). Suitable for Citroen 2CV. Or. No.: A44278A

Quality: 3

• Suitable for this article
• Tie rods rubber, at the front axle. Suitable for Citroen 2CV4 + 2CV6.
  2,77 €
• Front axle sliding sheet metal at the steering unit. Suitable for Citroen 2CV. Or. No.: AM44279
  7,83 €
• Front axle sliding sheet metal, safety sheet. (Sliding sheet metal on the steering unit). Suita
  1,55 €
• Screw M7x12, e.g. to fix the steeringwheel 2cv, screw is galvanized
  0,51 €

Front axle sliding sheet metal at the steering unit. Suitable for Citroen 2CV. Or. No.: AM44279

Quality: 3

Front axle sliding sheet metal, safety sheet. (Sliding sheet metal on the steering unit). Suitable for Citroen 2CV. Or.Nr.A44295

Quality: 3

• Suitable for this article
• Screw M7x12, e.g. to fix the steeringwheel 2cv, screw is galvanized
  0,51 €

Front axle pipe - steering gear in the exchange. Suitable for Citroen 2CV4 + 2CV6. Top outdated, all bearings and pinions are accurately bedded in and measured. The steering worm and the gear rack are re-tooled with grease nipple. To lubricate thus at any time from the outside. 250 euros Old part deposit.

Quality: 1

Gear rack thrust piece (in the steering gear). Suitable for Citroen 2CV.

Quality: 3

Gear rack ring in the axle tube (steering gear). Suitable for Citroen 2CV. Reproduction. First oversize. Outside diameter: about 34,2mm. Inside diameter: 27,5mm.

Quality: 4

• Suitable for this article
• Gear rack ring, rivets for the securement of the guide ring. Suitable for Citroen 2CV, all year
  1,17 €

Gear rack ring in the axle tube (steering gear). Suitable for Citroen 2CV. Reproduction. Standard dimension. Outside diameter: about 34,00mm. Inside diameter: 27,50mm.

Quality: 4

• Suitable for this article
• Gear rack ring, rivets for the securement of the guide ring. Suitable for Citroen 2CV, all year
  1,17 €

Gear rack ring in the axle tube (steering gear). Suitable for Citroen 2CV. Reproduction. Second oversize. Outside diameter: about 34,3mm. Inside diameter: about 27,5mm.

Quality: 4

• Suitable for this article
• Gear rack ring, rivets for the securement of the guide ring. Suitable for Citroen 2CV, all year
  1,17 €

Gear rack ring in axle tube 2CV. Reproduction. Made in European Union. Outside diameter 34,05mm, inside diameter 27,50mm.

Quality: 3

Gear rack ring in axle tube 2CV. Reproduction. Made in European Union. Outside diameter 34,10mm, inside diameter 27,50mm.

Quality: 3

• Suitable for this article
• Gear rack ring, rivets for the securement of the guide ring. Suitable for Citroen 2CV, all year
  1,17 €

Gear rack ring in axle tube 2CV. Reproduction. Made in European Union. Outside diameter 34,15mm, inside diameter 27,50mm.

Quality: 3

• Suitable for this article
• Gear rack ring, rivets for the securement of the guide ring. Suitable for Citroen 2CV, all year
  1,17 €

Gear rack ring in axle tube 2CV. Reproduction. Made in European Union. Outside diameter 34,25mm, inside diameter 27,50mm.

Quality: 3

• Suitable for this article
• Gear rack ring, rivets for the securement of the guide ring. Suitable for Citroen 2CV, all year
  1,17 €

Gear rack ring, rivets for the securement of the guide ring. Suitable for Citroen 2CV, all years of construction.

Quality: 3

Gear rack steering unit, 19 teeth. Suitable for Citroen 2CV, starting from year of construction 1955. This gear rack is only Installed by vehicles, which have an steering worm with 7 teeth. Or. No.: A4424b

Quality: 4

Gear rack steering unit, starting from Orga No. 2276. Suitable for Citroen 2CV. 32 teeth, overall length: 370mm. Reproduction.

Quality: 3

• Suitable for this article
• Gear rack ring, rivets for the securement of the guide ring. Suitable for Citroen 2CV, all year
  1,17 €

Steering rack, up to Orga no. 2276. Suitable for Citroen 2CV (steering pinion with 7 teeth). 24 teeth, total length: 365mm. Replica

Quality: 3

• Suitable for this article
• Gear rack ring, rivets for the securement of the guide ring. Suitable for Citroen 2CV, all year
  1,17 €